How to Brew Your Own Beer

Author Info

Last Updated: February 17, 2024 Approved

VIDEO

Brewing your own beer at home is easy, inexpensive, fun, and will most likely produce a brew far superior to that watery canned stuff. You'll also become like Bacchus to your beer buddies! We'll lay out the basic steps to get started, and show you how you can grow your skills and expand the varieties of beer you produce.

Ingredients

Malt extract (liquid or dried)
Hops
Specialty grains
Yeast (varieties all depend on the type of beer you are brewing, and these ingredients are all available in kits)

Part 1

Part 1 of 3:

Preparation

Download Article

1
Keep it clean. As any experienced brewer will tell you, 80% of the secret of success is cleanliness. Thoroughly clean and sanitize everything that is going to come in contact with your beer. The easiest way to do that is to use an electric dishwasher set at the high heat setting or use a powdered cleanser such as PBW (Powdered Brewery Wash).
- Do not use a scrubber that will scratch the surface of whatever you're scrubbing—pathogens love to grow in the grooves left behind, and they're almost impossible to sanitize. Rinse well, then soak briefly in a bleach or iodine solution.
2
Rinse everything well. Rinse off bleach before using items using very clean potable or distilled water. Do not assume tap water is sanitized for rinsing brewing equipment.
- If you're using bleach to sanitize, add one ounce (30ml) of bleach to five gallons (19 liters) of cold water, followed by one ounce (30ml) of white vinegar. Do not mix the bleach and vinegar together before adding to the water! The vinegar will make the water more acidic, which helps the bleach sanitize.
- Do not rinse iodine solutions, let equipment drip dry instead.
- Note that bleach can cause unwanted flavours in your beer, and requires rinsing, which can introduce microorganisms to your sterilized equipment. If you want to sterilize your equipment properly, use either a food-grade cleanser or sanitizer such as One Step No-Rinse Sanitizer, which requires no rinsing; or an iodine solution such as BTF Iodophor.
- Remember, in beer brewing, you can do just about anything you want, and add anything you want, to make whatever kind of beer you want—but proper sanitizing is the MOST important thing you can do. Take the time and the energy to do it right.
Advertisement
That includes cleaning and sanitizing as outlined, and also includes having all your ingredients prepared and measured in advance.

Part 2

Part 2 of 3:

Brewing

Download Article

1
Take notes. Before you begin your foray into home brewing, get a notebook, and note down everything you do—the cleaning process, what strain of yeast, the amount and specific type of malt, what variety of hops, and any specialty grains or other ingredients used to produce your beer.
- This will allow you to reproduce any given brew, or provide a basis for experimentation and improvement.
2
Steep your grains.^{[1]
X
Research source} Put any specialty grains into a grain bag (a mesh bag to contain the grains—like a tea bag, only a lot bigger) and steep them in the large stock pot in three gallons (10 liters) of hot water (around 150°F (66°C) for about 30 minutes.
- Remove the grains and allow the water to drip out of the grain bag, into the pot. Do not squeeze the bag, because you may extract tannins that will give your beer an astringent flavor.
3
Add the malt extract and bring everything to a boil. The hops are usually added at various intervals to add flavor, bitterness, or aroma and the times will be spelled out for you in the kit's instructions for your style of beer.
- In general, hops added early in the boil will contribute more bitterness, but at the expense of flavor and aroma. Hops added at the end of the boil will have a more pronounced flavor and aroma, but will not contribute significantly to the bitterness of the beer.
- Consider dry hopping your beer if you are looking for a brighter and less bitter flavor.^{[2]
  X
  Research source}
4
Chill your wort. After you have boiled the liquid (called wort—pronounced wərt), you need to cool it as quickly as possible. The easiest way is to put the whole pot in a sink or bathtub that is filled with ice water.^{[3]
X
Research source}
- You can gently stir the wort to help expedite the cooling, but try not to splash or aerate the wort while it's still hot (it can make for some funky flavors).
- Once it's around 80°F (27°C) you are ready to transfer it to the fermenter.
5
Pour the cooled wort into your fermenter. After the wort has cooled and before fermentation starts is the one and only time that splashing is encouraged. Yeast need oxygen, and splashing the wort as you pour it into the fermenter will deliver that.
- Once fermentation has started, you want to minimize exposure to air, as it will lead to off flavors and aromas.
- Using a large strainer (usually cheapest at restaurant supply stores), scoop the hops out—you've already got all the good stuff out of them. (If using a carboy, strain the wort as you pour it into the carboy).
- Add water to make five gallons (20 liters). You are now ready to "pitch" (add) the yeast. Some yeast requires that you "bloom" (stir with warm water to activate) them prior to pitching, others do not. You may find that even those that don't require blooming will start working faster if you do bloom them first, but it's usually no big deal.
- Put the lid on your fermenter (or stopper in your glass carboy) and affix the air-lock to the top. Put the fermenter in a dark area that stays a fairly consistent room temperature (for ales...lagers need refrigeration to ferment properly). In about 24 hours, you should notice the air-lock happily bubbling away, if it hasn't started doing anything after 48 hours, you might have a problem such as dead yeast.

Part 3

Part 3 of 3:

Bottling

Download Article

1
Prepare for bottling! After a week or so, the activity from the airlock will slow to a crawl. Leave it alone for two weeks measured from the time you first started the brewing/fermenting. The beer is now ready for bottling. Your kit probably came with some priming sugar or DME(dried malt extract).^{[4]
X
Research source} This is used to provide carbonation to your beer once it is in the bottle.
- Boil the sugar in a little water and cool it. Then, add it to the empty, cleaned and sanitized bucket with the spigot or to your fermented beer.^{[5]
  X
  Research source}
2
Transfer the brew. Use your cleaned and sanitized plastic tubing as a siphon to transfer the beer as gently as possible—so that there's little or no aeration—from the fermenter to the bottling bucket with the priming sugar solution in it. Try not to get any of the sediment (trub) from the fermenter into the bottling bucket.
- Attach your cleaned and sanitized bottle filler to your clean and sanitized plastic tubing, the other end of the tubing attaches to the bottom end of the spigot. (If you are only using one bucket, it is important to let the fermented beer settle after stirring in the priming sugar solution. There is sediment on the bottom (trub) that will lend an off flavor to your beer).
3
Get your thoroughly cleaned and sanitized bottles ready. If you are using a bottling bucket, just open the spigot and put the bottle filler in a bottle. Push the bottle filler to the bottom and that will let the beer flow.
- If using the one bucket method, fill the tube (attached to the bottle filler) with water and put the open end in the fermented beer and place the bottle filler in a glass, or a bottle or the sink, press down to let the water flow out and start the beer flowing in the tube like a siphon. Fill each bottle just to overflowing, then remove the bottle filler: this leaves an almost perfect airspace at the top of the bottle. Cap the bottle with your handy bottle capper, and repeat until all the bottles are full.
Store the bottles for at least a week preferably two at about room temperature, then refrigerate.
When you're ready, open a bottle, and pour carefully into a glass. Leave about a quarter inch in the bottle—the sediment tastes a little yeasty, and will give you serious beer farts.

Video

Read Video Transcript

Community Q&A

Search

Add New Question

Question

Where can I get beer bottles?

Community Answer

Specialty brewing shops will have both bottles and caps. The sealer shown is a fancy one, but simpler cheaper versions are also available. Typically the people operating specialty brewing shops will advise you sensibly!

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 16
Question

How much stuff do I need? How much yeast, malt extract, and hops?

Community Answer

It depends on how much you are going to make. Look for recipes to determine how much you need.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 14 Helpful 28
Question

Do I have to dry my homemade malt once germinated or can I mash with moisture in it?

Community Answer

You need to dry it to stop the fermentation and make your finished product taste better.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 2 Helpful 9

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Start collecting non-screw top bottles well in advance of beginning this hobby, you will need about 50 to bottle a standard batch. This is a good excuse to start buying premium brands. Also old recyclable glass soft drink bottles and some champagne bottles are outstanding (a dark beer in a coke bottle is stealthy to say the least), and can often be found at yard sales.

Thanks
Helpful 19 Not Helpful 2
DON'T USE BLEACH! Use a brewery specific sanitizer like "StarSan" or an iodine based food grade sanitizer!

Thanks
Helpful 20 Not Helpful 12
A bottle brush will be handy for cleaning the bottles. A good thermometer will be useful for many things.

Thanks
Helpful 11 Not Helpful 5

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Be careful when adding the sugar to your bottles for carbonation. If you add too much they can explode!

Thanks
Helpful 41 Not Helpful 6
When boiling the wort, watch for boil-overs. That malt extract is some squirrelly stuff when it starts boiling. Same goes for boiling the DME for priming.

Thanks
Helpful 28 Not Helpful 7
Do NOT use "Brewer's Yeast" as sold in health food stores, etc. This is dead yeast, and won't work!

Thanks
Helpful 36 Not Helpful 19
If you are using a glass carboy, never pour hot wort directly into it, it will break from the temperature difference.

Thanks
Helpful 26 Not Helpful 16
Before adding extract to the boiling water, turn off the heat. Stir it in well, but gently, before turning the heat back on. This helps to avoid scorching the extract, and minimizes the chance of boil-overs.

Thanks
Helpful 17 Not Helpful 10
Check your country's laws about brewing your own brew. A few American states require permits.

Thanks
Helpful 8 Not Helpful 25

Things You'll Need

Large stock pot that can hold 3 gallons (11.4l). Preferably with a lid.
5 to 6 gallon (20-23l) food grade plastic bucket with an air-tight lid (or glass carboy) A second bucket with a spigot at the bottom will be good too.
Air lock (available from home brew shops)or you can use one from an aquarium store for about $20USD less
At least 2 cases of 12oz (355ml) bottles (non-screw tops work best). 500 milliliters (16.9 fl oz) bottles can be used if you would like to drink by the pint (may only be available in plastic with screw tops).
Bottle filler (plastic tube with a spring-loaded nozzle at one end that keeps the beer from pouring all over the place)
About 5 feet (1.5m) of food grade plastic tubing that will fit your bottle filler (for transferring the beer from the bucket/carboy to your bottles)
Bottle capper
Caps